IMG_20200802_195318606.jpg
My screw collar looks different from yours. It has only one hole. I think that is part of the problem. The transmission is on a K engine. Thanks again for your help Active Unanswered
Search found 15 matches
- Sun Aug 02, 2020 7:07 pm
- Forum: Engines & Powertrain
- Topic: 1xe Transmission issue
- Replies: 2
- Views: 1669
Re: 1xe Transmission issue
My screw collar looks different from yours. It has only one hole. I think that is part of the problem. The transmission is on a K engine. Thanks again for your help
- Sun Aug 02, 2020 11:27 am
- Forum: Engines & Powertrain
- Topic: 1xe Transmission issue
- Replies: 2
- Views: 1669
1xe Transmission issue
Hello, about 4 yrs ago I had my transmission rebuilt that included new clutch disks and bearings. After about 250 hours of service it started to slip. I adjusted it one notch and it no longer slips but now I have a new problem. It is extremely difficult to get it out of gear(it requires two arms to ...
- Wed Sep 11, 2019 1:54 pm
- Forum: Finishing
- Topic: topside plank discoloration
- Replies: 3
- Views: 5383
Re: topside plank discoloration
Thank you for the replies and possible course of action. This will be a winter project and will keep you posted
- Sun Sep 08, 2019 11:35 am
- Forum: Finishing
- Topic: topside plank discoloration
- Replies: 3
- Views: 5383
topside plank discoloration
Does anyone know what causes the discoloration of the topside planks along the seams? Also I was wondering what the remedy
is and how to prevent it in the future. Thanks in advance
- Fri Sep 06, 2019 6:34 am
- Forum: Engines & Powertrain
- Topic: oil line fitting size
- Replies: 2
- Views: 1818
Re: oil line fitting size
Thank you for the reply. It is greatly appreciated
- Wed Sep 04, 2019 4:24 pm
- Forum: Engines & Powertrain
- Topic: oil line fitting size
- Replies: 2
- Views: 1818
oil line fitting size
Hello, Does anyone happen to know what size this fitting is? The reason I am asking is I am trying to attach an oil pressure test gauge and 1/4 npt and also 1/4 flare doesnt fit along with compression. Its the oil line tee off of an M series block. Thanks in advance
- Tue Jul 09, 2019 12:53 pm
- Forum: Engines & Powertrain
- Topic: Oil pressure drop
- Replies: 3
- Views: 2468
Re: Oil pressure drop
Perhaps another thing to check would be water leaking into the oil cooler and making it too thin??
- Mon Jul 01, 2019 6:44 pm
- Forum: Engines & Powertrain
- Topic: KLC Oil Cooler Bypass
- Replies: 3
- Views: 2277
Re: KLC Oil Cooler Bypass
There are others on this site who have way more knowledge than me, but I would say you should be ok. The oil does not get that hot that fast.
- Mon Jun 24, 2019 10:22 am
- Forum: Engines & Powertrain
- Topic: oil leak
- Replies: 6
- Views: 3522
Re: oil leak
OK thanks for the advice. There is no "this side up" on my replacement gasket. There is however one side that is smooth and the other side has ridges around the cylinder bore holes. I assume that the side with the ridges faces down and the smooth side is up?? I know assume can be a dangerous word so...
- Mon Jun 24, 2019 8:44 am
- Forum: Engines & Powertrain
- Topic: oil leak
- Replies: 6
- Views: 3522
Re: oil leak
ok, will do. Hopefully its just the gasket. I was told the motor is low time and it hadn't been used in awhile so maybe its from sitting??? Also is there anything i should coat the gasket with or just install it dry. Thanks in advance.
- Mon Jun 24, 2019 8:30 am
- Forum: Engines & Powertrain
- Topic: oil leak
- Replies: 6
- Views: 3522
Re: oil leak
Thank you for solving the mystery. I guess this is one of the reasons you keep a spare handy.
- Sun Jun 23, 2019 5:32 pm
- Forum: Engines & Powertrain
- Topic: oil leak
- Replies: 6
- Views: 3522
oil leak
Hello, I was wondering if anyone has an idea of what is causing oil to pool on the top of the cylinder head nuts?? I checked the torque on them and they are at 65 pounds.
- Sat Feb 11, 2017 10:16 am
- Forum: Engines & Powertrain
- Topic: K Valve Seat
- Replies: 0
- Views: 2025
K Valve Seat
Hello, I have a post war model K with worn valve guides. The compression on all cylinders is good and the rest of the motor seams to be ok. I've done some research on the forum and it appears to be of universal consent that new exhaust valves with a 45 degree seat insert cut into the head is a given...
- Wed Oct 28, 2015 5:48 pm
- Forum: Engines & Powertrain
- Topic: paragon 1XE output flange
- Replies: 2
- Views: 1707
Re: paragon 1XE output flange
Thanks!! That did it!
- Wed Oct 28, 2015 12:16 pm
- Forum: Engines & Powertrain
- Topic: paragon 1XE output flange
- Replies: 2
- Views: 1707
paragon 1XE output flange
Hello all: I am having difficult in removing the flange from the above transmission. So far I have removed the big nut on the end of it and put a puller on it but it doesn't seem to want to come all of the way out. Also the shaft is keyed. Am I missing something or do I just need to apply more press...