Active Unanswered
Search found 2046 matches
- Sat Feb 11, 2023 3:18 pm
- Forum: Engines & Powertrain
- Topic: KLC piston height
- Replies: 7
- Views: 2212
Re: KLC piston height
Anythings possible. Until you pull them and check the numbers on the side and measure them you won't know.
- Sat Feb 11, 2023 10:05 am
- Forum: Engines & Powertrain
- Topic: KLC piston height
- Replies: 7
- Views: 2212
Re: KLC piston height
Without removing the pistons and measuring them it is hard to say. But 1/16" is the compression height difference between a K series piston and a KL series piston.
- Sun Jan 08, 2023 10:41 am
- Forum: Fiberglass - Hardware & Rigging
- Topic: Restoration '73 XK 19
- Replies: 1
- Views: 5269
Re: Restoration '73 XK 19
Post good photos of what you need. Find a boat like yours and blow up the parts you need.
- Sat Dec 31, 2022 11:20 am
- Forum: Odds & Ends
- Topic: Brass or stainless - ceiling boards?
- Replies: 1
- Views: 1527
Re: Brass or stainless - ceiling boards?
Should be some sort of bronze. Oval Reed & Prince
- Wed Dec 07, 2022 11:18 am
- Forum: Fiberglass - Engines & Powertrain
- Topic: 283 rubber mounts
- Replies: 4
- Views: 7302
- Tue Dec 06, 2022 4:48 pm
- Forum: Engines & Powertrain
- Topic: Water Pump Rebuilding
- Replies: 7
- Views: 2178
Re: Water Pump Rebuilding
Numbers
- Tue Dec 06, 2022 4:44 pm
- Forum: Engines & Powertrain
- Topic: Water Pump Rebuilding
- Replies: 7
- Views: 2178
Re: Water Pump Rebuilding
That's not a Chevrolet pump. If it were the part number would be on the surface where the gasket is when removed.
- Tue Dec 06, 2022 4:41 pm
- Forum: Engines & Powertrain
- Topic: Drilling Camshaft??
- Replies: 2
- Views: 1603
Re: Drilling Camshaft??
Pressurized oil is supposed to go in a manual gear. Blow in the end of the crank to see if it was drilled.
- Mon Nov 14, 2022 9:46 am
- Forum: How to Use Boat Buzz
- Topic: Trailering Boat on Highway
- Replies: 3
- Views: 1741
Re: Trailering Boat on Highway
I prefer covered. Stops stuff from flying out. Have eyelets in the skirt every couple feet to secure the cover to the trailer.
- Sun Sep 25, 2022 7:38 pm
- Forum: How to Use Boat Buzz
- Topic: 1963 Sea Skiff 24 weight?
- Replies: 2
- Views: 1954
Re: 1963 Sea Skiff 24 weight?
Weight 3397-4397 Beam 9ft 1in.
- Tue Sep 06, 2022 7:50 pm
- Forum: Engines & Powertrain
- Topic: V8 Water Pump
- Replies: 24
- Views: 20686
Re: V8 Water Pump
You need to remove the four 7/16" wrench size bolts. The part number is hidden there.
- Tue Sep 06, 2022 8:15 am
- Forum: How to Use Boat Buzz
- Topic: 1954 Sportsman 8v battery -6 volt system
- Replies: 4
- Views: 2811
Re: 1954 Sportsman 8v battery -6 volt system
Has the charging system been re-worked to charge the 8V?
- Mon Aug 08, 2022 9:07 am
- Forum: Engines & Powertrain
- Topic: 1955 Chris Craft 21’ Capri with Hemi
- Replies: 1
- Views: 1104
Re: 1955 Chris Craft 21’ Capri with Hemi
I read the Maintenance manual cover to cover and all I found was:
Torque 298lbs @ 2800 RPMs
Horsepower 200 @ 3800 RPMs
Horsepower usually peaks then drops off before the engine Maxs out.
Torque 298lbs @ 2800 RPMs
Horsepower 200 @ 3800 RPMs
Horsepower usually peaks then drops off before the engine Maxs out.
- Fri Jul 29, 2022 1:00 pm
- Forum: Ask Hagerty
- Topic: 1950 hercules water pump
- Replies: 1
- Views: 1885
Re: 1950 hercules water pump
Thermostat was optional. They are in the accessory catalog. Makes it run much better.
- Sat Jul 23, 2022 4:50 pm
- Forum: Engines & Powertrain
- Topic: High Oil Pressure in KFL
- Replies: 5
- Views: 2199
Re: High Oil Pressure in KFL
Fine Wood Boats has the gaskets. Here is the end of the oil pump that you will find when you remove that plate. Call 815 344-9663 M -Th to order.
- Wed Jul 13, 2022 11:39 am
- Forum: Electrical Systems
- Topic: Stern Light for 61 Capri
- Replies: 2
- Views: 2719
Re: Stern Light for 61 Capri
Peter,
The parts are hardware store items. Tubing and delrin. Gravity holds the pole in. That's why they are often missing.
The parts are hardware store items. Tubing and delrin. Gravity holds the pole in. That's why they are often missing.
- Sat Jul 09, 2022 8:28 am
- Forum: Engines & Powertrain
- Topic: K carburetor float level
- Replies: 5
- Views: 3286
Re: K carburetor float level
B175 12 is the flame arrestor part number. See http://www.finewoodboats.com/Zenith%20Float%20Chart.jpg for a chart.
- Thu Jul 07, 2022 9:00 am
- Forum: Electrical Systems
- Topic: KFL won't start after it sits for 20 mins
- Replies: 8
- Views: 3403
Re: KFL won't start after it sits for 20 mins
A KFL should have a timing marker at about 1 O'clock between the two bolts that hold the front flange to the block. Matches to a dimple on the flywheel.
- Fri Jul 01, 2022 8:22 am
- Forum: Engines & Powertrain
- Topic: No (low) power in cylinders 4,5, & 6
- Replies: 2
- Views: 1344
Re: No (low) power in cylinders 4,5, & 6
Switch the carbs and see what happens.
- Wed Jun 22, 2022 1:28 pm
- Forum: Engines & Powertrain
- Topic: Name Plate Restoration
- Replies: 2
- Views: 1440
Re: Name Plate Restoration
Probably easier to buy new ones from http://www.finewoodboats.com/Tags.htm
- Fri Jun 17, 2022 8:43 am
- Forum: Engines & Powertrain
- Topic: Frost/Freeze Plugs
- Replies: 5
- Views: 1738
Re: Frost/Freeze Plugs
If it is a disc style I would replace it. Yes clean whatever you can.
- Thu Jun 16, 2022 2:18 pm
- Forum: Engines & Powertrain
- Topic: Frost/Freeze Plugs
- Replies: 5
- Views: 1738
Re: Frost/Freeze Plugs
There are two types. One has sides and is referred to as "cup style" I use a socket to install. The other is like a large contact lens. "Disc style" I'd replace that style and install with a large punch.
- Tue Jun 07, 2022 6:55 pm
- Forum: Engines & Powertrain
- Topic: Oil Filter
- Replies: 2
- Views: 1448
Re: Oil Filter
If it were me I'd install a spin-on filter kit. Make life easier trying to change the filter later on.
- Mon Jun 06, 2022 7:06 pm
- Forum: Engines & Powertrain
- Topic: Vapor Lock Issues
- Replies: 3
- Views: 1563
Re: Vapor Lock Issues
Ditto
Captain Nemo wrote: ↑Mon Jun 06, 2022 6:16 pmDid you rule out the coil? They can fail when hot and start back up when cooled back down.
- Fri Apr 22, 2022 8:47 am
- Forum: Ask Hagerty
- Topic: Hagerty discontinues classic boat insurance
- Replies: 3
- Views: 3774
Re: Hagerty discontinues classic boat insurance
I sure miss Carla.
- Fri Apr 22, 2022 8:44 am
- Forum: How to Use Boat Buzz
- Topic: Stern Boarding Ladder ?
- Replies: 1
- Views: 2377
Re: Stern Boarding Ladder ?
My U-22 has a transom ladder. It was custom made. Most runabout ladders are. Here is the factory Chris-Craft boarding ladder.
- Fri Mar 04, 2022 1:56 pm
- Forum: Engines & Powertrain
- Topic: K Engine Head Corner Stud Mod
- Replies: 1
- Views: 1691
Re: K Engine Head Corner Stud Mod
Put bolts in the square corners. That's the way it came from the factory.
- Thu Jan 27, 2022 2:21 pm
- Forum: Odds & Ends
- Topic: What is this
- Replies: 3
- Views: 3001
Re: What is this
It's a self bailer. Make sure it is clean and not cracked
- Sun Jan 16, 2022 11:59 am
- Forum: Engines & Powertrain
- Topic: 6 or 12 volt battery
- Replies: 2
- Views: 1707
Re: 6 or 12 volt battery
Depends on the year. Look on the coil or voltage regulator. Up to 1956 or so was 6 volt. Switched to 12 volt in 1957.
- Sat Jan 15, 2022 10:41 am
- Forum: Engines & Powertrain
- Topic: Hot K exhaust elbow
- Replies: 2
- Views: 1635
Re: Hot K exhaust elbow
What Captain Nemo says is correct. You don't want water in that area as it may get in to the internal part of the engine.