Active Unanswered
Clum Switch Lettering
Moderators: Don Ayers, Al Benton, Don Vogt
-
- Posts: 246
- Joined: Tue Oct 30, 2007 2:47 pm
- Contact:
Clum Switch Lettering
Looking for suggestions / help painting the white letters on my Clum Switch.
I watched a few youtube videos, looking for someone who has done.
Thanks
Tom
I watched a few youtube videos, looking for someone who has done.
Thanks
Tom
Re: Clum Switch Lettering
a very small brush and a steady hand.
1938 Chris Craft 17' Deluxe Runabout "Jennifer II"
- maritimeclassics
- Posts: 700
- Joined: Sat Mar 03, 2007 4:35 pm
- Location: Traverse City, Mi
- Contact:
Re: Clum Switch Lettering
I have used a tooth pick to paint them.
Family member of Chris Craft founder
Owner of Maritime Classics
http://www.maritimeclassics.com
Ph# 231-486-6148
Restoration Projects:
1936 25' Gar Wood Custom
1947 Ventnor Hydroplane
1957 17' Deluxe Runabout
1948 25' Chris Craft Sportsman Twin
1959 19' Sliver Arrow Hull #75
1929 26' Chris Craft Custom Runabout
1937 25' Chris Craft Custom Runabout
Owner of Maritime Classics
http://www.maritimeclassics.com
Ph# 231-486-6148
Restoration Projects:
1936 25' Gar Wood Custom
1947 Ventnor Hydroplane
1957 17' Deluxe Runabout
1948 25' Chris Craft Sportsman Twin
1959 19' Sliver Arrow Hull #75
1929 26' Chris Craft Custom Runabout
1937 25' Chris Craft Custom Runabout
-
- Posts: 246
- Joined: Tue Oct 30, 2007 2:47 pm
- Contact:
Re: Clum Switch Lettering
Thank you both for you help. I should probably do this before I do a plumbing repair in the house!
- Matt Smith
- Posts: 921
- Joined: Wed Oct 26, 2005 4:14 pm
- Location: Reedville VA,
- Contact:
Re: Clum Switch Lettering
I have tried this on other stuff. And I have tried to go back in time to figure out how they did it in the day. They would have not done one at a time. It would have been a process. I have an old one and may try this first so you dont waste a good finish on yours. I have learned that there is a wipe off part of this. Fill and wipe so to speak. The tooth pick way is the closest to filling, on drop at a time. But the wipe has to be also done. On metal I have wiped with a flat wiper.But that is the type that is embossed vs debossed. I will take a crack at it. Stay tuned.
1948 25' Chris Craft Sportsman
1937 16' Special Racer
1968 40' Rice Trawler
1968 11' Crab Skiff
2018 Hole in my head
WoodyBoater.com
1937 16' Special Racer
1968 40' Rice Trawler
1968 11' Crab Skiff
2018 Hole in my head
WoodyBoater.com
-
- Posts: 246
- Joined: Tue Oct 30, 2007 2:47 pm
- Contact:
Re: Clum Switch Lettering
Here is the finished product. Testers modeling paint put in with a toothpick slightly over filled. At 55 F it took 35 minutes to slightly
dry enough to wipe the surface with a very small amount of thinner without pulling all the paint out of the indentations. After wiping once I let it setup again for about 8 minutes. Finish clean up carefully. I started at 3 minutes dry time and worked my way up to 35. Obviously there was a lot of downtime waiting for the paint to dry. The hole process took 7 hours. That was a bit of a learning curve.
dry enough to wipe the surface with a very small amount of thinner without pulling all the paint out of the indentations. After wiping once I let it setup again for about 8 minutes. Finish clean up carefully. I started at 3 minutes dry time and worked my way up to 35. Obviously there was a lot of downtime waiting for the paint to dry. The hole process took 7 hours. That was a bit of a learning curve.
Re: Clum Switch Lettering
Looks like a great job.
1938 Chris Craft 17' Deluxe Runabout "Jennifer II"
-
- Posts: 246
- Joined: Tue Oct 30, 2007 2:47 pm
- Contact:
Re: Clum Switch Lettering
Thanks
Re: Clum Switch Lettering
Great job Tom! Looks like you’re the new go to guy on this.
Who is online
Users browsing this forum: No registered users and 6 guests